Hybrid street lighting kit for wind turbine and solar panel SHLP 8M-50/400/500
Lighting column with a wind generator and a solar panel and LED module SHLP 8M-50/400/500 - works without a mains. The system is autonomous and receives energy completely from solar and wind energy, which is unlimited in reserves and is harmless to the environment. A set of autonomous lighting system consists of:
- headrest (bracket for mounting the lamp);
- anchorage device for mounting the support;
- photovoltaic panels with mounting on a support;
- wind generator and mounting for it;
- LED module;
- smart controller that combines battery and lamp driver functions;
- gel battery;
- anti-vandal, sealed box for mounting the battery in the ground.
The use of a hybrid (hybrid) street lighting system allows the use of wind and sun energy. These systems work in tandem for the fastest charging of the gel battery, and also reserve each other depending on weather conditions. At night or in cloudy and rainy days, the controller can use the sensors to calculate the daylight and automatically turn on the light.
The biggest advantage of outdoor hybrid LED lamps is their complete independence from energy sources other than the sun and wind. Due to this, they can be installed in places where access to standard electricity is difficult or impossible.
For the production of the hybrid unit, we use only high quality materials that provide long-lasting and trouble-free operation. The intelligent electronics system with the controller protects the battery from overloads and heavy discharge. Hybrid lighting systems have the ability to program glow duration (smoke) and illumination control after dusk using wireless controls.
Characteristics of SHLP 8M-50/400/500
|Wind generator||Rated power: 24 V - 400 W Maximum output power: 500 W Number of blades: 3 pcs Wind speed at which the wind generator starts 2.5 m/s|
Power: 2 x 270 W = 540 W Panel type: polycrystalline, tempered glass 3.2 mm thick, coated, absorbing solar radiation, panels tested in accordance with IEC 61215 for snow loads up to 5400 Pa (approx. 5.4 kN/m2) and IEC 61730. Certificates available: ISO 9001, ISO 14001, OHSAS 18001, ISO 2859-1
|LED module||Power: 50W
Operating voltage: DC 24V
LED life: >50,000 hours
Degree of protection: IP66
Luminous flux: >5500 lm
Operating temperature: -30 ℃ .. +60 ℃ Weight: 6 kg Adjustable when mounting, mounting angle of the luminaire and rotatable around the support axis by 360° regardless of the direction and angle of installation of the solar panels
|Controller||2 х MPPT 20A - 24V Protection rating: IP68 Weight: 2 х 2 kg = 4 kg The switch-on lighting time is determined by an integrated dusk sensor (light sensor). Included is an infrared remote control for programming and controlling the lamp (smoke). The MPPT controller, unlike PWM, allows the most efficient use of all the power of the solar panel (by tracking the maximum power generated by the solar panel) and the stages of the battery charge (charge, saturation, equalization, charge support) and on this basis determines what current must be fed into the batteries.|
|Battery||2 x 200AH 12V - NPG Gel Battery Specialized for Solar Powered Equipment, Fully Sealed, Has Full Deep Discharge Cycle, No Maintenance Weight 2 x 58 kg = 116 kg|
|Battery box||PVC material Weight: 3 kg Designed to be installed underground, avoiding high summer temperatures or too cold winter temperatures. It is vandal-resistant and waterproof. Able to dissipate heat from the battery. Included is a PVC pipe with a system for forced recirculation of crankcase gases for cables.|
|Support and bracket||
Height: 8 m Luminaire installation height: 6.5 m Conical reinforced support, made in accordance with EN 40-5: 2002 and EN 40-2 in S355 steel (headrest and battery mount rack in S235 steel). Corrosion protection - hot dip galvanizing according to EN ISO 1461. Vehicle impact resistance: class "0" in accordance with EN 12767. Certificates of resistance in accordance with EN 40-3-1, safety class "B", class "2" . The design conforms to the standard: EN 1090. The calculation of the support is made for the II category of terrain and the pressure of the wind speed of 300 Pa (depending on the place of installation we perform the calculation of endurance in accordance with the wind district of Ukraine and the terrain category)
|Anchor device||F180-V43 M30|
|Work time||8-10 hours a day (with full power of the LED module), the battery capacity is designed for up to 4 full cloudy, rainy and windy days.|
|Installation guidelines||This set is suitable for areas with an average annual peak solar power of 4 ~ 3.5 hours per day|
|Certificates||A Ukrainian Certificate of Compliance is available. Scope:
– ДСТУ EN 55015:2014
– ДСТУ EN 61000-3-3:2014
– ДСТУ EN 60335-1:2015
|Producer country of support||Poland|
Possibility of forming the support with powder paint according to the RAL palette
Supplied with Bluetooth interface with software for programming and remote control of the fixture
The system configuration may be changed depending on the client or project requirements
Additional information by phone or e-mail. Depending on the quantity, additional discounts are possible.