USD
0
My order

Set of autonomous park lighting kit on solar battery Stolb SLP CUT-4M

Article: SLP-CUT4/30/830

Set of autonomous park lighting on the solar panel Stolb SLP CUT

Stolb SLP CUT is an advanced solution in autonomous street lighting systems, which combines simplicity of design, aesthetics and high efficiency.

The main advantages of our kit from the available systems on the market:

Integrated battery in the support

Due to the placement of the battery directly in the middle of the lighting pole, there is no need to place it in special boxes on the pole or in the ground. This solution not only prevents the battery from being stolen, but also simplifies the design of the support and creates an aesthetically pleasing design that lacks external boxes and anti-vandal systems in the form of devices that restrict access to the upper part of the support.

360° bracket for solar panel

Placing autonomous lighting kits on the ground requires the orientation of the solar panel to the south for maximum energy generation by the autonomous system, and the light module over the roadway or pedestrian zone, so the Stolb SLP CUT kit uses a specially designed mount that allows you to orient the panel regardless of light and individually for each support.

Intelligent MPPT controller with LED driver function

The use of the MPPT controller allows you to get the most out of the solar panel generation compared to the PWM controller by tracking the point of maximum power, which is extremely important for stand-alone lighting systems. At the same time, this controller combines the function of the LED driver, and allows you to adjust the brightness of the lighting in 4 time intervals (dimming).

Delivery set:

  • metal support of lighting with a height of 4000 mm. Corrosion protection is provided by powder coating with preliminary cleaning of the structure and application of zinc-containing primer. There is a choice of any RAL palette for painting the support without changing the cost. Additionally, gas-thermal zinc spraying at a height of 0.25 m from the support flange in accordance with EN 40-5: 2002 is used to protect the support flange.
  • LED module with T3 optics with a power of 30 - 45 W;
  • LiFePO4 battery with BMS controller;
  • bracket for mounting a photovoltaic panel with the ability to rotate 360°;
  • anchor device for mounting the support;
  • solar panel;
  • MPPT intelligent controller, which combines the functions of battery charge and lamp driver;

The system is completely autonomous and works without connection to an external network. During the day, when the sun shines, the system generates electricity and accumulates it in the battery. At dusk, the controller automatically turns on the light.


Features Stolb SLP CUT

Solar panel

 

Power: 330 W Panel type: 3.2 mm thick polycrystalline tempered glass, covered with a coating that absorbs solar radiation, the panels are tested according to IEC 61215 for snow loads up to 5400 Pa (approx. 5.4 kN / m2) and IEC 61730. Certificates available : ISO 9001, ISO 14001, OHSAS 18001, ISO 2859-1

LED module

Power: 30-45 W.

Operating voltage: DC 24V

Service life of LEDs:> 50,000 hours

Degree of protection: IP66

Luminous flux:> 3600 lm

Operating temperature: -30 ℃  +60 ℃

Controller

MPPT 10A - 24V Degree of protection: IP68 Weight: 1 kg Time of switching on of the lamp is defined by definition of voltage on the solar panel. The MPPT controller, unlike the PWM, allows the most efficient use of all the power of the solar panel (by tracking the maximum power generated by the solar panel).

Battery

LiFePO4, 30AH 24V with thermal protection and BMS controller. Suitable for operation at temperatures of -25 ℃ +60 ℃. The battery is equipped with a BMS controller, which monitors the charging process of the battery, as well as the temperature of its operation.

Support and bracket

 

Height: 4 m. Powder coating, zinc-containing primer. There is a choice of any RAL palette for painting the support without changing the cost. Additionally, gas-thermal zinc spraying at a height of 0.25 m from the support flange in accordance with EN 40-5: 2002 is used to protect the support flange.

Anchor device

FP4

Operating time

8-12 hours per day (at full power of the LED module), the battery capacity is designed for up to 3 full cloudy, rainy and windy days.

Installation recommendations

This kit is suitable for areas with an average annual peak solar capacity of 4 ~ 3.5 hours per day

Country-manufacturer of support

Ukraine

Additional features

 

  • Possibility of head lighting of a support by powder paint according to the RAL palette
  • Possibility of delivery with the Bluetooth interface together with the software for programming and remote control of the lamp
  • The system configuration can be changed depending on the requirements of the client or the project

 

 

Be the first to review
New review or comment
Login with
Rate the product
Send
Height, m
4
Power, W
30 40
Color temperature
$1 380
В наявності
  • Independent removal from the point of issue;
  • Courier delivery across Kiev;
  • Delivery across Ukraine is carried out by services Nova Poshta, SAT.

More about delivery conditions →

  • Non-cash payment for a legal entity;
  • Payment for goods when ordering with delivery in Ukraine;
  • Payment by Visa / MasterCard payment card;
  • In cash.

Learn more about payment terms →

 

Warranty from the manufacturer 36 months, exchange / return of goods within 14 days.
More about returning and exchanging goods →

 

 

Characteristic
Title Set of autonomous park lighting kit on solar battery Stolb SLP CUT-4M
Up